PC Speed

Search
Votes / Statistics
Rating 
9.5/10
Hits: 8,936
Downloads: 1,775
Votes: 2
Your vote:
My Atarimania
Bookmark and Share
Comments (0)

Screenshots - PC Speed

PC Speed atari screenshot
PC Speed atari screenshot
PC Speed atari screenshot
PC Speed atari screenshot
PC Speed atari screenshot
PC Speed atari screenshot
PC Speed atari screenshot

Information - PC Speed

GenreHardware - Emulation / OS FixingYear1990
Language[unknown]PublisherCOMPO Software
DeveloperSACK ElectronicDistributor
ControlsMouseCountryUnited Kingdom
Box / InstructionsEnglishSoftwareEnglish
Programmer(s)

[unknown]

LicenseCommercial
SerialST TypeST / 0.5MB
ResolutionLow / Medium / HighNumber of Disks1 / Single Sided
Dumpdownload atari PC Speed DownloadMIDI
Protection

Additional Comments - PC Speed

Other versions with the same title:


Sack Electronic (version 1.25) (), Sack Electronic (version 1.4) ().

PC Speed accelerator hardware required.

Instructions - PC Speed

                 Important informations about PC-SPEED
                 
1  On the 68000 CPU of the new MEGA ST is a little accesory print  
   with a IC 74LS74.
   In order to secure the work of PC-SPEED, it is necessary to     
   conect the PIN 12 of this print with a 220 Ohm resistor at PIN  
   12 of the 68000.
   It is also possible to do without the print, while conecting    
   the yellow wire, wich is placed on the accesory print, directly 
   with PIN 12 of the 68000 CPU.

2  PC-SPEED tries, while booting, to execute the bootsector.
   If you by mistake try to boot from a TOS formatted disk, PC-    
   SPEED crashes.

3  The TIMER.COM program on the PC-SPEED disk hands over the TOS-  
   time to DOS.

4  PC-SPEED emulates the Olivetti 640*400 pixel graphic card.
   Many PC-programs (GEM,MS-WINDOWS etc.) support this.

                Upgradings for the PC-SPEED V1.30

5  If you have a serial PC-MOUSE you can use this MOUSE under      
   ST-mode by executing PC-MOUSE.PRG .

6  MEGADISC.SYS is a driver for Ramdisk, which runs in the memory  
   over 1 Megabyte.
   Usage: In CONFI G.SYS. following lines are to insert.
   DEVICE= [drive:] [\path] \MEGADISK.SYS
   No options are required.
   Following capacities are available:
    0   MB at MEGA2
    1.4 MB at MEGA2.5
    2.9 MB at MEGA4
   Attention: Do not install on 512KB or 1MB ST.

7  Extended Memory support (XMA)!!! (on ST > 1MB)
   Precisely: INT15 funktion 87HEX and 88HEX are supported.
   Following capacities are available:
    0    MB at MEGA1,1040,520,260 ST
    0.9  MB at MEGA2
    1.4  MB at MEGA2.5
    2.9  MB at MEGA4
   Hint: NORTON SI gives you the additional XMA Capacity.
   Usefullness: from DOS 3.3 on the VDISK.SYS ramdisk-driver can   
   use the extended memory.
   Usage: Insert the following line in your CONFIG.SYS:
   DEVICE= [drive:] [\path] \VDISK.SYS [ capacity in KB ] /E
   Note: when using big ramdisks, it is necessary to increase the
   number of entries in the table of contents.
   The default givings give space for 64 entries.
   By using XMA difficulties may occur if Programms use the        
   special Funktions of the 80286 Prozessor which are not
   supported by the NEC V30.
   Precisely: The V30 does not have a protected-mode.
   Note that the Extended Memory is not equivalent to the Expanded
   Memory.
   Expanded Memory need special Hardware-Cards on PC's or the
   capability of a 80386 Prozessor.

8  You can use your ST-Mouse under DOS.
   Note the Keyboard/Mouse Option in the PCS_INST.PRG.
   The following entries are possible:
   RS232 :You can use the RS232 interface up to 2400Bd under DOS   
   (COM1).
   It is also possible to connect a serial microsoft-kompatible    
   Mouse.
   MICROSOFT-MOUSE: The ST-Mouse appears under DOS as a microsoft-
   kompatible mouse.
   In order to work with the mouse you need the equivalent
   mouse-driver which is supplied in many DOS-programs.
   Note: There are mouse-drivers, that only support Mouse-Systems
   compatible mice. Do not use these drivers.
   If a mouse-driver is named MSMOUSE.COM it is possible that
   the mouse-driver is only compatible to mouse-systems mice.
   The RS232 Interface is not supported in this mode.
   CURSOR-MOUSE: In this mode the ST-mouse does only emulate the
   funktion of the cursor-keys.

9  If you type the ( key on the external numberblock at the same   
   time with the I key the screen can be inverted.

                Upgradings for the PC-SPEED V1.40

10 You can access up to 24 Partitions on your harddisk by using    
   the ADD_PART.SYS driver.
   The usage of more than 1 harddisk is possible.
   Usage: Insert the following lines in the CONFIG.SYS:
   DEVICE=[Drive:][\Path]\ADD_PART.SYS
   No Options are required.
   After rebooting ADD_PART.SYS reports the new drivenumbers.
   Up to 2 Partitions the ADD_PART.SYS is not required.
   Note: Please choose the option MULTI in the PCS_INST.PRG .
   NORM and ICD remained due to compatibility and still function
   as the older PC-SPEED Versions.
   You can use Partitions up to 32MB ( using AHDI 3.0 ).
   Only the drivenumbers C and D are restricted to 16MB.

11 In the CGA mode you can display the TANDY 1000 resolution !!!
   Games often support this resolution.
   The TANDY 1000 can display 320 x 200 pixel in 16 Colors.

12 You can adjust the steprate on both drives A and B by using the
   PCS_INST.PRG .
   Normally 3 1/2 Inch Drives requires 3ms.
   5 1/4 Inch drives requires 6ms.
   Very slow drives requires 12ms.

13 With the PCS_OPT.COM programm you can increase the
   compatibility of PC-SPEED.
   The PCS_OPT.COM programm optimized the DOS operating system for
   PC-SPEED.
   Even very critical PC-programm are now supported.
   Hint: Execute the PCS_OPT.COM programm with your AUTOEXEC.BAT .

14 PC-SPEED is also available for the new ATARI STE !!!
   By fitting the PC-SPEED no soldering is necessary anymore.

                Upgradings for the PC-SPEED Mouse driver.

15 Now a Microsoft-compatible mouse driver MOUSE.COM is supplied
   with AT-SPEED and PC-SPEED. The file MOUSE.COM and MTEST.EXE    
   are copyrighted products from Naksha (Jersey) Limited.
   To install the mouse driver, add the following line into your   
   AUTOEXEC.BAT file:

        MOUSE/R3
   The option '/R3' is explained below.

   You may also start the program by typing in the file name with  
   or without options from the command line.

   Note: To use your mouse with AT-SPEED or PC-SPEED the option to 
   use a Microsoft-compatible mouse must have been set with the    
   installation program (see instruction manual).

   To show the options with Naksha's MOUSE.COM type in from the
   command line:

        MOUSE/H
   Then the following options are shown:


      =================================
      Naksha Mouse Driver V2.01
      (C) 1990 Naksha (Jersey) Limited
      =================================
      Valid command line options are:

      /1      - Use Serial Port COM1.
      /2      - Use Serial Port COM2.
      /3      - Use Serial Port COM3. port 3E8, IRQ 4.
      /4      - Use Serial Port COM4. port 2E8, IRQ 3.
      /R0     - Set Ballistic Motion OFF.
      /Rn     - Set Ballistic Motion Rate (n = 1 - 9).
      /Np, i  - Use Hexadecimal I/O Port (p) and Decimal IRQ level 
                (i).
      /P      - Use PS2 Compatible Pointing Device Port.
      OFF     - Release Mouse Driver and Tidy Up Memory.
      /? Help  also /H.

      To use this mouse driver with AT-SPEED/PC-SPEED you get good 
      results with:

        MOUSE/R3 (Normal mouse response)
        ...             ...
        MOUSE/R9 (Fast mouse response)

16  To switch the mouse driver off, type in from the command line:

       MOUSE OFF


17  To test the response of the mouse you may use MTEST.EXE. Also  
    you can check the response of the mouse buttons on your mouse.
    The above mentioned mouse driver must have been installed      
    before you can run MTEST, otherwise you will get an error      
    message. To test the mouse, type in from the command line:

        MTEST

                Upgradings for the PC-SPEED V1.50

18  ATARI LASER-printer supported. Read LASER.DOC.

19  PC-SPEED instal progrom now complet under GEM.

20  With VIDMOD.COM you can change under MS-DOS your screen        
    emulation. If you start the program you see how to handle on   
    the screen.

21  You can run PC-SPEED now also as a ACCESORY. Read              
    ACCESORY.DOC.

--

ACC.DOC 03/12/90 Compo Software


    Use of PC-SPEED as a desk accessory (PC_SPEED.ACC)
    ==================================================

To use PC-SPEED as a desk accessory your ST will need 2 or 4 MB of 
RAM!!
Copy the installed version of PC_SPEED.PRG to the boot drive (A: 
or C: with hard disk) and rename the program file to PC_SPEED.ACC.
When you reset the computer the ST will boot again, PC-SPEED will 
be installed into the desk menu.
After clicking on the desk menu entry, ie on the GEM DEsktop or a 
GEM application, the common PC-SPEED start-up screen will show up.
If this is not the case an error message will appear on your 
screen as PC-SPEED is unable to allocate memory, caused by the 
currently running GEM program which has allocated all available 
memory. However in some programs (eg. Tempus) it's possible to 
adjust (and store) the memory consumption.
Control-Alternate-Insert brings you back in TOS.

--

LASER.DOC 12/10/90 Compo Software


    Using the ATARI SLM 804 laserprinter with PC-SPEED.
    ===================================================

To use the laserprinter your ST will need 2 or 4 MB of RAM!!!

Install the laserprinter in PCS_INST.PRG. Quit and save the op- 
tions within the program file PC_SPEED.PRG.
Then create a folder. Copy the installed version of PC_SPEED.PRG 
within this folder, also DIAB630.PRG with the font files and 
SDUMP.PRG (which have been supplied with your laserprinter).

Start PC_SPEED.PRG now. The common messages of DIAB630.PRG and 
SDUMP.PRG will appear on the screen.
Now the DOS application is able to print via LPT1, the output will 
be redirected to the ATARI laserprinter on the DMA port.
You may print a hardcopy of the screen by pressing [Shift] and 
[PrtScr].
Alternatively the printerport (Centronics) may be used via LPT2. 
If this not happens it's possible that:
-   the laser driver has already been installed (booted from the   
    AUTO folder...) and has been executed for the second time. An  
    error message         was shown.
-   the font files were not loaded because the program couldn't    
    find these files or were incomplete. Error messages will be    
    displayed.
-   when you use PC-SPEED as a desk accessory the laserprinter     
    cannot be used caused by a different memory configuration.

Ads - PC Speed

PC Speed Atari ad

Article - PC Speed


PC Speed Article PC Speed Article
About Us - Contact - Credits - Powered with Webdev - © Atarimania 2003-2019